Nico Helfesrieder

Herr M.Sc.

Wissenschaftlicher Mitarbeiter "Antriebssysteme und -regelung"
Institut für Steuerungstechnik der Werkzeugmaschinen und Fertigungseinrichtungen

Kontakt

+49 711 685 82452
E-Mail

Seidenstr. 36
70174 Stuttgart
Deutschland
Raum: 5.102

Sprechstunde

nach Vereinbarung

Fachgebiet

Topologieoptimierung
Angewandte FE-Simulation

Publikationen

Veröffentlichungen:

2023
1. Steinle, Lukas ; Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander ; Montazeri, Ali ; Wang, Jinfan: Decentralized Motion Control for a Novel Planar Motor Intralogistics System. In: 2023 IEEE 32nd International Symposium on Industrial Electronics (ISIE), 2023 IEEE 32nd International Symposium on Industrial Electronics (ISIE) : IEEE, 2023
  - BibTeX
  - Link
  BibTeX
  @inproceedings{Steinle_2023, author = {Steinle, Lukas and Helfesrieder, Nico and Lechler, Armin and Verl, Alexander and Montazeri, Ali and Wang, Jinfan}, booktitle = {2023 IEEE 32nd International Symposium on Industrial Electronics (ISIE)}, doi = {10.1109/isie51358.2023.10227969}, month = {06}, publisher = {IEEE}, title = {Decentralized Motion Control for a Novel Planar Motor Intralogistics System}, url = {https://doi.org/10.1109%2Fisie51358.2023.10227969}, year = 2023 }
  Link
  https://doi.org/10.1109%2Fisie51358.2023.10227969
2. Helfesrieder, Nico ; Neubauer, Michael ; Lechler, Armin ; Verl, Alexander: Anisotropic Damping and Stiffness of laminated steel parts using adhesive bonding – an empirical influence study. In: Procedia CIRP, Procedia CIRP. Bd. 120 : Elsevier BV, 2023, S. 428–433
  - BibTeX
  - Link
  BibTeX
  @inproceedings{Helfesrieder_2023, abstract = {Layered part manufacturing enables part topology to be optimized internally by structuring individual layers separately, which is especially promising for large machine parts. However, the resulting part properties as a function of the selected manufacturing parameters are largely unexplored. Therefore, this paper investigates the impacts of the slicing direction, the sheet thickness as well as the adhesive on anisotropic damping and stiffness values of adhesively bonded steel parts. A cantilever beam of symmetric cross-section is chosen as an easy-to-manufacture geometry. Three redundant specimens were prepared for each of six parameter variations investigated within this study, resulting in a total of 18 investigated beams. The results indicate highly anisotropic stiffness and damping as a function of the layer build-up direction and it was found that the modal damping rises with increasing amount of adhesive. These findings must be taken into account for future applications of layered lightweight machine parts and their simulative predictability should be studied.}, author = {Helfesrieder, Nico and Neubauer, Michael and Lechler, Armin and Verl, Alexander}, doi = {10.1016/j.procir.2023.09.014}, issn = {2212-8271}, journal = {Procedia CIRP}, pages = {428–433}, publisher = {Elsevier BV}, title = {Anisotropic Damping and Stiffness of laminated steel parts using adhesive bonding – an empirical influence study}, url = {http://dx.doi.org/10.1016/j.procir.2023.09.014}, volume = 120, year = 2023 }
  Link
  http://dx.doi.org/10.1016/j.procir.2023.09.014
3. Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander: Leichtbau durch schichtweise LLM-Fertigung – zur Anisotropie der Bauteileigenschaften. In: Konstruktion, Konstruktion. Bd. 75, VDI Fachmedien GmbH and Co. KG (2023), Nr. 09, S. 42--44
  - BibTeX
  - Link
  BibTeX
  @article{2023, author = {Helfesrieder, Nico and Lechler, Armin and Verl, Alexander}, doi = {10.37544/0720-5953-2023-09-42}, journal = {Konstruktion}, number = 09, pages = {42--44}, publisher = {{VDI} Fachmedien {GmbH} and Co. {KG}}, title = {Leichtbau durch schichtweise {LLM}-Fertigung {\textendash} zur Anisotropie der Bauteileigenschaften}, url = {https://doi.org/10.37544%2F0720-5953-2023-09-42}, volume = 75, year = 2023 }
  Link
  https://doi.org/10.37544%2F0720-5953-2023-09-42
2022
1. Jud, Oliver ; Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander: Vorspannungsnachstellung an Kugelgewindetrieben/Preload adjustment on ball screws – Methods for increasing service life due to automatic adjustment of preload force. In: wt Werkstattstechnik online, wt Werkstattstechnik online. Bd. 112, VDI Fachmedien GmbH and Co. KG (2022), Nr. 05, S. 282--287
  - BibTeX
  - Link
  BibTeX
  @article{Jud_2022, author = {Jud, Oliver and Helfesrieder, Nico and Lechler, Armin and Verl, Alexander}, doi = {10.37544/1436-4980-2022-05-12}, journal = {wt Werkstattstechnik online}, month = {05}, number = 05, pages = {282--287}, publisher = {{VDI} Fachmedien {GmbH} and Co. {KG}}, title = {Vorspannungsnachstellung an Kugelgewindetrieben/Preload adjustment on ball screws {\textendash} Methods for increasing service life due to automatic adjustment of preload force}, url = {https://doi.org/10.37544%2F1436-4980-2022-05-12}, volume = 112, year = 2022 }
  Link
  https://doi.org/10.37544%2F1436-4980-2022-05-12
2021
1. Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander: Strukturoptimierte Maschinenkomponenten mit hoher Dämpfung. In: Antriebstechnik, Antriebstechnik. Bd. 3/2021 (2021), Nr. 3, S. 40--43
  - BibTeX
  - Link
  BibTeX
  @article{Helfesrieder.2021, author = {Helfesrieder, Nico and Lechler, Armin and Verl, Alexander}, issn = {0722-8546}, journal = {Antriebstechnik}, number = 3, pages = {40--43}, title = {Strukturoptimierte Maschinenkomponenten mit hoher Dämpfung}, url = {http://digital.antriebstechnik.de/antriebstechnik-3-2020/65318893/40}, volume = {3/2021}, year = 2021 }
  Link
  http://digital.antriebstechnik.de/antriebstechnik-3-2020/65318893/40
2. Helfesrieder, Nico ; Neubauer, Michael ; Lechler, Armin ; Verl, Alexander: Hybrid manufacturing of topology optimized machine tool parts through a layer laminated manufacturing method: Practical validation using the example of a bearing block. In: Production Engineering Research and Development, Production Engineering Research and Development. (2021)
  - BibTeX
  - Link
  BibTeX
  @article{Helfesrieder.2021b, abstract = {Load-oriented lightweight structures are commonly designed based on topology optimization. For machine tool parts, they enable the reduction of moving masses and therefore increase the resource and energy efficiency of production systems. However, this usually results in complex part structures that are difficult or impossible to produce using conventional manufacturing methods. In this paper, a hybrid layer laminated manufacturing (LLM) method is proposed enabling manufacturing of topology-optimized machine tool parts. The method is referred to as hybrid, as the subtractive structuring of metal sheets is combined with the additive joining of the sheets by adhesive bonding. This enables enclosed inner cavities without support structures, which are used to approximate the optimal density distribution from a topology optimization via manufacturing. The proposed LLM method is validated on the basis of a bearing block of a ball screw feed drive. A experimental study in the time and frequency domain on a test rig confirms the principle suitability of the LLM method for the production of industrial applicable lightweight components.}, author = {Helfesrieder, Nico and Neubauer, Michael and Lechler, Armin and Verl, Alexander}, doi = {10.1007/s11740-021-01095-7}, file = {Helfesrieder, Neubauer et al. 2021 - Hybrid manufacturing of topology optimized:Attachments/Helfesrieder, Neubauer et al. 2021 - Hybrid manufacturing of topology optimized.pdf:application/pdf}, issn = {0944-6524}, journal = { Production Engineering Research and Development}, month = {12}, title = {Hybrid manufacturing of topology optimized machine tool parts through a layer laminated manufacturing method: Practical validation using the example of a bearing block}, url = {https://doi.org/10.1007/s11740-021-01095-7}, year = 2021 }
  Link
  https://doi.org/10.1007/s11740-021-01095-7
2020
1. Schütz, Andreas ; Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander: Automatisierte Werkstückfixierung - Formadaptive Aufspannung von Schalenelementen für Bearbeitungsaufgaben mit Industrierobotern. In: wt Werkstattstechnik online, wt Werkstattstechnik online. Bd. 110 (2020), Nr. 01–02, S. 80–85
  - BibTeX
  - Link
  BibTeX
  @article{Schuetz2020, author = {Schütz, Andreas and Helfesrieder, Nico and Lechler, Armin and Verl, Alexander}, journal = {wt Werkstattstechnik online}, language = {Deutsch}, month = {02}, number = {01-02}, pages = {80-85}, title = {Automatisierte Werkstückfixierung - Formadaptive Aufspannung von Schalenelementen für Bearbeitungsaufgaben mit Industrierobotern}, url = {https://www.werkstattstechnik.de/wt/currentarticle.php?data[article_id]=92636}, volume = 110, year = 2020 }
  Link
  https://www.werkstattstechnik.de/wt/currentarticle.php?data[article_id]=92636
2. Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander: Method for generating manufacturable, topology-optimized parts for Laminated Layer Manufacturing. In: Procedia CIRP, Procedia CIRP. Bd. 93 (2020), S. 38--43
  - BibTeX
  - Link
  BibTeX
  @article{Helfesrieder.2020, abstract = {The great flexibility provided by generative manufacturing offers immense potential for the structural component optimization. However, this freedom needs to be utilized by appropriate CAx tools. In this paper, we present a novel slicing method, enabling the automatic generation of topology-optimized Laminated Layer Manufacturing (LLM) parts. With this method a part of arbitrary shape can be automatically sliced and equipped with a uniform virtual grid that is suitable for manufacturing. The optimal density distribution is then mapped onto the individual slices and locally approximated through the introduction of variably shaped cavities. By using 3D modeling techniques all LLM sheets are modeled parametrically and assembled automatically. To verify the functionality of the presented method, it is applied to two practical parts and compared with a conventional topology optimization method.}, author = {Helfesrieder, Nico and Lechler, Armin and Verl, Alexander}, doi = {10.1016/j.procir.2020.04.048}, issn = {22128271}, journal = {Procedia CIRP}, pages = {38--43}, title = {Method for generating manufacturable, topology-optimized parts for Laminated Layer Manufacturing}, url = {http://www.sciencedirect.com/science/article/pii/S2212827120306144}, volume = 93, year = 2020 }
  Link
  http://www.sciencedirect.com/science/article/pii/S2212827120306144
2019
1. Helfesrieder, Nico ; Neubauer, Michael ; Lechler, Armin ; Verl, Alexander: Hochautomatisierte Roboterzelle mit adaptiver Werkstückaufspannung für die komplexe Holzbearbeitung. In: agt agile technik verlag (Hrsg.) HOB Die Holzbearbeitung, HOB Die Holzbearbeitung. (2019), Nr. 3/2019, S. 57–58
  - BibTeX
  BibTeX
  @article{helfesrieder2019hochautomatisierte, author = {Helfesrieder, Nico and Neubauer, Michael and Lechler, Armin and Verl, Alexander}, editor = {agt agile technik verlag}, journal = {HOB Die Holzbearbeitung}, number = {3/2019}, pages = {57-58}, title = {Hochautomatisierte Roboterzelle mit adaptiver Werkstückaufspannung für die komplexe Holzbearbeitung}, year = 2019 }
2. Menze, Christian ; Becker, Dina ; Stehle, Thomas ; Möhring, Hans-Christian ; Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander: Spanende Bearbeitung mit Industrierobotern und Bearbeitungszentren: Vergleichende Analyse der erzielbaren Bauteilqualität in der Holzbearbeitung. In: wt Werkstattstechnik online, wt Werkstattstechnik online. Bd. 109 (2019), Nr. 9, S. 650–655
  - BibTeX
  BibTeX
  @article{Menze.2019, author = {Menze, Christian and Becker, Dina and Stehle, Thomas and M{\"o}hring, Hans-Christian and Helfesrieder, Nico and Lechler, Armin and Verl, Alexander}, journal = {wt Werkstattstechnik online}, number = 9, pages = {650-655}, title = {Spanende Bearbeitung mit Industrierobotern und Bearbeitungszentren: Vergleichende Analyse der erzielbaren Bauteilqualit{\"a}t in der Holzbearbeitung}, volume = 109, year = 2019 }
2018
1. Helfesrieder, Nico ; Lechler, Armin ; Verl, Alexander: Mehr Steifigkeit bei weniger Gewicht. In: MM Maschinenmarkt, MM Maschinenmarkt., Vogel Communications Group GmbH & Co. KG (2018), Nr. 019, S. 112–113
  - BibTeX
  BibTeX
  @article{helfesrieder2018steifigkeit, author = {Helfesrieder, Nico and Lechler, Armin and Verl, Alexander}, journal = {MM Maschinenmarkt}, month = {09}, number = 019, pages = {112-113}, publisher = {Vogel Communications Group GmbH & Co. KG}, title = {Mehr Steifigkeit bei weniger Gewicht}, year = 2018 }

Nico Helfesrieder

Kontakt

Sprechstunde

Fachgebiet

Publikationen

2023

BibTeX

Link

BibTeX

Link

BibTeX

Link

2022

BibTeX

Link

2021

BibTeX

Link

BibTeX

Link

2020

BibTeX

Link

BibTeX

Link

2019

BibTeX

BibTeX

2018

BibTeX

Zielgruppe

Formalia

Services

Organisation

Nico Helfesrieder

Kontakt

Sprechstunde

Fachgebiet

Publikationen

2023

BibTeX

Link

BibTeX

Link

BibTeX

Link

2022

BibTeX

Link

2021

BibTeX

Link

BibTeX

Link

2020

BibTeX

Link

BibTeX

Link

2019

BibTeX

BibTeX

2018

BibTeX

So erreichen Sie das ISW

Zielgruppe

Formalia

Services

Organisation